Midges Dust Extraction System - the blog

Progress, although now I’m not sure whether it’s a shed or a gay bar.

0_1501741123184_shed-15.jpg

and here’s the beginning of something. It’s not what you think, so breath easy. Actually it’s there so you can breath easy - I have a pair of 10" 600cfm fans, one of which will be attached to the outside by this pair of 6" outlets - should go a long way to removing that fine airborne dust. Not that I’d know much about that.

0_1501741242118_shed-14.jpg

last edited by bitingmidge

I never imagined the inside of a gay bar looking like that. :D

Good to see some progress.

So what’s the story with the katoom?

Mick

Belongs to the kid who used to live next door. He went off to the army and I said it couldn’t stay unlocked in his mum’s carport, so now I have this giant bit of decoration - it’s the 390 and goes just about as hard as any motorbike needs to!

Cheers,

P

@Joker all that limewashed ply has gone a beaut pinky colour (as it tends to do). I’m sure you’d love it in person!

@bitingmidge
And you know this from trying it out? KTM does manage to wring lots of ponies out of their motors. They tend to be a mite less long lived or reliable than some of their competitors but they do go hard. I’m lusting after their new 2 stroke road registerable enduro bike. Transfer port fuel injection, oil injection, balancer shaft, more than a foot of suspension travel at both ends, 6 speed box, 112 kg with a full tank and at least 50 ponies. Would chew through the back tyre very quickly but more than offset by the limited wear on the front due to it spending lots of time up in the air. Just need to have a small lotto win!

Mick

Finally finished the shed garden structures today - I dug the first holes four years ago. If you look carefully in the above pic, you’ll see a glimpse of it through the back door. Actually that’s through the back door via the bathroom (two way) and laundry, but anyway the last of the lattice panels is up and waiting for the passionfruit vine to recover from its vigorous prune.

I’m thinking about naming the joint “Sleeper World”
0_1502105425832_DickyWorld-15.jpg

last edited by bitingmidge

Is it not somewhat unseasonable for you to be working on the house & not the boat?

administrators

I’m with you Midge, don’t see a need to hurry.

Good work

@bitingmidge said in Midges Dust Extraction System - the blog:

I’m thinking about naming the joint “Sleeper World”
0_1502105425832_DickyWorld-15.jpg

Noice!
Hmmm, might copy the curved sleeper stairs at the rental.

Mick

@JMick said in Midges Dust Extraction System - the blog:

Hmmm, might copy the curved sleeper stairs at the rental.

They are a little complicated… the maths is simple enough, when you know the outer radius of the stair, calculate the perimeter of a circle of that radius, and divide by 200mm to get the number of sleepers that will fit around the perimeter, then calculate the perimeter of a circle 1200 less (or the width of the stair) and divide by the number of sleepers - this will give you the width of the sleeper at the narrow end.

All you have to do is rip the resulting wedge of each sleeper (in my case 17mm) and look what happens!

Because I only want to do it once, I didn’t lay them on the ground either (they are H3), I used H4 fence posts as joists and bits of old water pipe as posts bolted to the joists. Beneath them is excavated to keep the bearers above the ground.

They look good though.

@bitingmidge said in Midges Dust Extraction System - the blog:

Because I only want to do it once…

I’ll only be doing it once also, not long before I sell the place. Will probably just lay them on sleepers dug into the ground and laid on pads of concrete. There is a pre-existing curved retaining wall I need to follow. Its curve is of varying radius so I’ll probably just chuck the sleepers on the ground with one end touching the curve and then overlap them to see how much I need to rip off. Will be a good workout for the 9" saw which hasn’t seen much action for a few years now…

Mick

@JMick said in Midges Dust Extraction System - the blog:

Will be a good workout for the 9"

Anything bigger than seven and a quarter is a bit scary for my skinny little arms!

@bitingmidge said in Midges Dust Extraction System - the blog:

@JMick said in Midges Dust Extraction System - the blog:

Will be a good workout for the 9"

Anything bigger than seven and a quarter is a bit scary for my skinny little arms!

pffft, you need to try a 16 5/16" Makita 5402NA:

alt text

Mick

No I don’t!

Although I have a slab here where the (aging) concretor cut the expansion joint with a 10 diamond blade fitted to an eight inch grinder - no guards and the blade spinning a couple of inches from the inside of his elbow. I asked him not to, but he just called me a sook… I guess that had ME covered in the event of an accident. Covered in blood probably if I’d stood around, but call me squeamish, I couldn’t watch.

Yeah, not good. You may have noticed in the pic above that the operator has retracted the bottom guard by hand, as you do, when you are cutting at an angle, leaving the entire bottom of the blade exposed. I shudder to think what would happen in the case of a kickback, it would probably disembowel him!

Mick

Bit of an update:

I haven’t mowed the backyard for a bit, but I think at last the reno is finished and I can get on with all those little maintenance jobs… like trying to find the back yard for starters:
0_1551232659184_2019_01_22 at 17-40-04.jpg

And the shed’s a bit tidier, some of the gadgets are actually connected to the dustie too, but it’s OK it’s not finished. Lots of junctions to make and adapt.

0_1551232746906_2019_01_16 at 11-32-13.jpg

Currently working on getting the 250mm dia exhaust to go out via two 150 pipes. Nothing like making an MDF transition to brighten up a Sunday afternoon.
1_1551232931280_2019_02_24 at 19-59-20.jpg

0_1551232931280_2019_02_24 at 19-58-35.jpg

@bitingmidge damn Id give anything to greenery like that. Drier than a ?? down here.

For those interested in dust extraction, Ive been gaining info from Dust Ex page on the WWF and placed an order with Perth outfit Pipesonline, they gave me a special deal on freight and if Id bought locally spent at least twice what they charged me including freight.

@tonto said in Midges Dust Extraction System - the blog:

@bitingmidge damn Id give anything to greenery like that. Drier than a ?? down here.

Photoshop!

For those interested in dust extraction, Ive been gaining info from Dust Ex page on the WWF and placed an order with Perth outfit Pipesonline, they gave me a special deal on freight and if Id bought locally spent at least twice what they charged me including freight.

AS you can see I’m pretty much sorted, but am making 6" fittings for the machines.

What’s the latest on BellMouths at WWF - is anyone making 'em for sale?

Looks like your connection to The Blokey Shed was lost, please wait while we try to reconnect.